Pin oak
Quercus palustris
Pin oak measures 1,510 lbf on the Janka scale, 17% harder than northern red oak.
- It sits in the top quarter of the list for both hardness and shrinkage across the face.
- Sapele has exactly the same Janka figure.
- Across all 155 woods it falls in the top fifth for T/R ratio.
U.S. hardwoodsU.S. softwoodsImported woodsNorthern red oak
Six measures
Pin oakU.S. hardwoods medianOther woods
Cupping tendency
2.2123rd highest of 1551.092.90Shrinkage across the face
9.5%radial 4.3%32nd highest of 1553.5%12.7%Janka hardness
1,510 lbf6,717 N37th hardest of 1557th of 53 U.S. hardwoods; 30% above the U.S. hardwoods median240 lbf3,680 lbfDensity
0.580.63 at 12% MC46th heaviest of 1550.250.96Bending strength
14,000 psi96.5 MPa63rd strongest of 1554,300 psi29,900 psiStiffness
1.73 M psi11.9 GPa69th stiffest of 1550.54 M psi4.06 M psi
How much it moves
Most of its movement runs along the rings (T/R 2.21): quartersawn, the same board would lose 0.26 in. instead of 0.57 in.
0.57 in.
off a 6-inch flatsawn board, green to oven-dry
- Tangential
- 9.5%
- Radial
- 4.3%
- Volume
- 14.5%
- T/R ratio
- 2.21 (131st most stable of 155)
End view, shrinkage drawn 3× life size.
Closest substitutes
- Laurel oak
20% softer · 3% lighter · shrinks 0.4 points more across the face
- Sugar maple
4% softer · 3% lighter · shrinks 0.4 points more across the face
- Northern red oak
15% softer · 3% lighter · shrinks 0.9 points less across the face
Among the oaks
2nd hardest of 15, lbf; the neighbours either side are shown, the rest are on the oaks page.
Laboratory values
Its most unusual laboratory figure is tension across the grain: the highest of the 73 woods with a published value.
| Property | Green | Dry, 12% MC | Change when dried | Metric, 12% MC |
|---|---|---|---|---|
| Tension perpendicular | 800psi | 1,050psi | +31% | 7.20MPa |
| Impact bending | 48in. | 45in. | −6% | 1,143mm |
| Shear parallel to grain | 1,290psi | 2,080psi | +61% | 14.3MPa |
| Compression perpendicular | 720psi | 1,020psi | +42% | 7.00MPa |
| Side hardness | 1,070lbf | 1,510lbf | +41% | 6,717N |
| Work to maximum load | 14in-lbf/in³ | 14.8in-lbf/in³ | +6% | 102kJ/m³ |
| Modulus of rupture | 8,300psi | 14,000psi | +69% | 96.5MPa |
| Modulus of elasticity | 1.32M psi | 1.73M psi | +31% | 11.9GPa |
| Compression parallel to grain | 3,680psi | 6,820psi | +85% | 47MPa |
Wood Handbook Table 5-3b, Table 4-3. Data & method · Guides