Yellow-cedar
Chamaecyparis nootkatensis
Yellow-cedar measures 580 lbf on the Janka scale, about 45% as hard as northern red oak.
- Of the three Chamaecyparis cedars in the handbook, none is heavier, and none has a higher T/R ratio.
- Across all 155 woods it falls in the top fifth for T/R ratio and in the bottom fifth for face shrinkage, radial shrinkage and volumetric shrinkage.
- On the Janka scale its nearest neighbours are jack pine at 570 lbf and red alder at 590 lbf.
U.S. hardwoodsU.S. softwoodsImported woodsNorthern red oak
Six measures
Yellow-cedarU.S. softwoods medianOther woods
Shrinkage across the face
6.0%radial 2.8%21st lowest of 1553.5%12.7%Cupping tendency
2.1430th highest of 1551.092.90Stiffness
1.42 M psi9.8 GPa39th most flexible of 1550.54 M psi4.06 M psiJanka hardness
580 lbf2,580 N41st softest of 15512th of 37 U.S. softwoods240 lbf3,680 lbfDensity
0.420.44 at 12% MC45th lightest of 1550.250.96Bending strength
11,100 psi76.5 MPa54th weakest of 1554,300 psi29,900 psi
How much it moves
Total movement is small, but most of it runs along the rings (T/R 2.14), so a flatsawn board still loses 2.1 times the width of a quartersawn one.
0.36 in.
off a 6-inch flatsawn board, green to oven-dry; quartersawn 0.17 in.
- Tangential
- 6.0%
- Radial
- 2.8%
- Volume
- 9.2%
- T/R ratio
- 2.14 (126th most stable of 155)
End view, shrinkage drawn 3× life size.
Closest substitutes
- Jack pine
2% softer · 5% lighter · shrinks 0.6 points more across the face
- Eastern hemlock
14% softer · 10% lighter · shrinks 0.8 points more across the face
- White fir
17% softer · 12% lighter · shrinks 1.0 points more across the face
Among the Chamaecyparis cedars
2nd hardest of 3, lbf.
Laboratory values
| Property | Green | Dry, 12% MC | Change when dried | Metric, 12% MC |
|---|---|---|---|---|
| Shear parallel to grain | 840psi | 1,130psi | +35% | 7.80MPa |
| Modulus of elasticity | 1.14M psi | 1.42M psi | +25% | 9.79GPa |
| Side hardness | 440lbf | 580lbf | +32% | 2,580N |
| Tension perpendicular | 330psi | 360psi | +9% | 2.50MPa |
| Modulus of rupture | 6,400psi | 11,100psi | +73% | 76.5MPa |
| Compression perpendicular | 350psi | 620psi | +77% | 4.30MPa |
| Compression parallel to grain | 3,050psi | 6,310psi | +107% | 43.5MPa |
| Work to maximum load | 9.20in-lbf/in³ | 10.4in-lbf/in³ | +13% | 71.7kJ/m³ |
| Impact bending | 27in. | 29in. | +7% | 737mm |
Wood Handbook Table 5-3b, Table 4-3. Data & method · Guides